Skip to main content

voltage

Voltage, is is the difference in potential between two points  in an electric field. also called electromotive force.

voltage is the pressure from an electrical circuit’s power source that pushes charged electrons (current).
water-analogy1.png          grater the voltage grater the flow of electric current. Voltage is symbolized by  V or E. The standard unit is the volt. One volt will drive one columb  (6.24 x 1018) charge.such as electronics through a resistance of one ohm.

Voltage can be direct or alternating. A direct voltage maintains the same polarity. In an alternating voltage, the polarity reverses direction periodically. The number of complete cycles per second is the frequency which is measured in hertz.
Labels:

Comments

  1. Kirchhoff laws | THE JARGONMay 14, 2017 at 2:34 AM

    […] are some simple relationships between currents and voltages of different branches of an electrical circuit. These relationships are determined by some basic […]

    ReplyDelete
  2. Mesh analysis | THE JARGONMay 14, 2017 at 4:55 AM

    […] Law.  It uses the mesh currents as the circuit variables. we can use Mesh Analysis to find out the voltage, current or power through a particular element or […]

    ReplyDelete
  3. THE JARGONJune 10, 2017 at 3:52 AM

    […] →1.1 Voltage […]

    ReplyDelete

Post a Comment

Popular posts from this blog

Lorentz force equation

  Lorentz Force Equation   The force experienced by current element in magnetic field is given as sum of force due to electric field and magnetic field.   Force due to electric field: A region is said to be characterized by an electric field if a particle of charge q moving with a velocity v experiences a force Fe, independent of v. The force, Fe, is given by              F e = qE ---------------------------------------- (1.1)                    E is the electric field intensity. Measured in newtons per coulomb (N/C) or volts per meter. Where volt is a newton-meter per coulomb. The line integral of E between two points A and B in an electric field region gives voltage between A and B. It is the work per unit charge done by the field in the movement of the charge from A to B. Force due to magnetic field: If a charged particle experiences a force which depends on v, then the region is said to be characterized by a magnetic field. The force, Fm, is given by                     F m =...
2 comments
Read more

relay

A relay is an electrically operated switch. These are remote control electrical switches that are controlled by another switch. A relay is used to isolate one electrical circuit from another. It allows a low current control circuit to make or break an electrically isolated high current circuit path. The basic relay consists of a coil and a set of contacts. The most common relay coil is a length of magnet wire wrapped around a metal core. When voltage is applied to the coil, current passes through the wire and creates a magnetic field. This magnetic field pulls the contacts together and holds them there until the current flow in the coil has stopped. The diagram below shows the parts of a simple relay. Operation: When a current flows through the coil, the resulting magnetic field attracts an armature that is mechanically linked to a moving contact. The movement either makes or breaks a connection with a fixed contact. When the current is switched off, the armature is usually returned by...
1 comment
Read more

Maxwell equations

Maxwell equations: The electric and magnetic fields are governed by a set of four laws, known as Maxwell’s equations. Maxwell’s equations form the basis for the entire electromagnetic field theory. Max well’s equations in integral form: 1. Faraday’s law:                         A time-varying magnetic field gives rise to an electric field. Specifically, the electromotive force around a closed path C is equal to the negative of the time rate of increase of the magnetic flux enclosed by that path, that is,      2. Ampere’s circuit law: Time varying electric fields give rise to magnetic fields. Specifically, the magnetomotive force (mmf) around a closed path C is equal to the sum of the current enclosed by that path due to actual flow of charges and the displacement current due to the time rate of increase of the electric flux (or displacement flux) enclosed by that path; that is,         3. Gauss law of electric field: Gauss’ law for the electric field states that electric charges give ...
2 comments
Read more