Skip to main content

inductor

An inductor is a passive electronic component that stores energy in the form of a magnetic field. In its simplest form, an inductor consists of a wire loop or coil. The inductance is directly proportional to the number of turns in the coil. Inductance also depends on the radius of the coil and on the type of material around which the coil is wound.

indictor 1.jpg

 

The standard unit of inductance is the Henry abbreviated H. This is a large unit. More common units are the micro Henry, abbreviated µH (1 µH =10-6H) and the milli Henry, abbreviated mH (1 mH =10-3 H). Occasionally, the nano Henry (nH) is used (1 nH = 10-9 H).

introduction-to-electronics-30-728.jpg

 

 

 

 

 

 

inductors in series & parallel :


inductor 2.jpg

applications :


Inductors are used extensively in analog circuits and signal processing. Applications range from the use of large inductors in power supplies, which in conjunction with filter capacitors remove  fluctuations from the direct current output.

 

 

 

 

 
Labels:

Comments

Post a Comment

Popular posts from this blog

Lorentz force equation

  Lorentz Force Equation   The force experienced by current element in magnetic field is given as sum of force due to electric field and magnetic field.   Force due to electric field: A region is said to be characterized by an electric field if a particle of charge q moving with a velocity v experiences a force Fe, independent of v. The force, Fe, is given by              F e = qE ---------------------------------------- (1.1)                    E is the electric field intensity. Measured in newtons per coulomb (N/C) or volts per meter. Where volt is a newton-meter per coulomb. The line integral of E between two points A and B in an electric field region gives voltage between A and B. It is the work per unit charge done by the field in the movement of the charge from A to B. Force due to magnetic field: If a charged particle experiences a force which depends on v, then the region is said to be characterized by a magnetic field. The force, Fm, is given by                     F m =...
2 comments
Read more

relay

A relay is an electrically operated switch. These are remote control electrical switches that are controlled by another switch. A relay is used to isolate one electrical circuit from another. It allows a low current control circuit to make or break an electrically isolated high current circuit path. The basic relay consists of a coil and a set of contacts. The most common relay coil is a length of magnet wire wrapped around a metal core. When voltage is applied to the coil, current passes through the wire and creates a magnetic field. This magnetic field pulls the contacts together and holds them there until the current flow in the coil has stopped. The diagram below shows the parts of a simple relay. Operation: When a current flows through the coil, the resulting magnetic field attracts an armature that is mechanically linked to a moving contact. The movement either makes or breaks a connection with a fixed contact. When the current is switched off, the armature is usually returned by...
1 comment
Read more

Transistor

Introduction: A transistor is a semiconductor device which is used to amplify the signals as well as in switching circuits. Generally, it consists of three terminals emitter(E), base(B) and collector(C) and two P-N junctions. It is one of the active components. It was invented by John Bardeen, William Shockley and Walter Brattain in 1948, in Bell Telephone Laboratories. Transistors are divided into different types depending on their construction and operation. Transistors are basically classified into two types; they are Bipolar Junction Transistors (BJT) and Field Effect Transistors (FET). The BJTs are again classified into NPN and PNP transistors. The FET transistors are classified into JFET and MOSFET. Junction FET transistors are classified into N-channel JFET and P-channel JFET depending on their function. MOSFET transistors are classified into Depletion mode and Enhancement mode. Again depletion and enhancement mode transistors are classified into N-channel JFET and P-channel. d...
2 comments
Read more